Solite fit guide
& size charts
Find your size for Solite boots, gloves and accessories, and learn how to heat-mould your 2.0 boots.
Heat-mouldable boots
Solite boot sizes
| UK boot size | US boot size | Reference foot length (cm) |
|---|---|---|
| 4 | 5 | 22.5 |
| 5 | 6 | 23.5 |
| 6 | 7 | 24.4 |
| 7 | 8 | 25.4 |
| 8 | 9 | 26.2 |
| 9 | 10 | 27.0 |
| 10 | 11 | 27.9 |
| 11 | 12 | 28.9 |
| 12 | 13 | 29.8 |

How to measure and fit
Stand on a sheet of paper with your heel against a wall. Mark the end of your longest toe and measure from the wall to the mark. Use the chart as a starting point, then check the sizing notes on the boot you’re buying.
For average or wide feet, start with your usual shoe size or go down half a size if you’re between whole sizes. A narrow or low-volume foot may suit a smaller boot. If you’ll wear 1 mm neoprene Heat Booster socks, allow room for them, especially if you have wide feet or are choosing a 5 mm boot.
Try your boots indoors before moulding. They should feel snug, with your heel seated and your toes comfortable. If they already feel loose, contact us for sizing advice before moulding.
Browse Solite boots by water temperatureGauntlets and mitts
Solite glove & mitt size chart
| Size | Hand length (cm) |
|---|---|
| XS | 17.8–18.5 |
| S | 18.5–19.1 |
| M | 19.1–19.7 |
| L | 19.7–20.3 |
| XL | 20.3–21.0 |

How to measure and fit
Measure from the tip of your middle finger to the first crease at the base of your palm. Use the same hand-length chart for the Ocena® gauntlets, split-mitts and full-mitts.
A glove should fit snugly without squeezing your fingers or restricting movement. If you fall on a size boundary, Solite generally recommends the larger size, especially with thicker gloves and mitts.
Shop the Ocena® glove rangeHow to heat-mould Solite 2.0 boots
Check the instructions supplied with your boots before starting. Work in a sink and use boiling water only. Keep children away from the sink and avoid ovens, microwaves and heat guns.
Prevent burns. Empty and cool each boot before trying it on. Never put your foot into a boot containing hot water.
- Roll down the cuffs and stand both boots upright in the sink. Put on the Heat Booster socks if you plan to wear them with the boots.
- Carefully pour freshly boiled water into each boot, stopping just below the join between the upper and sole. Leave the water in the boots for five minutes.
- Empty one boot carefully and rinse the inside with cold water. Check the temperature by hand before putting it on. If it feels hot, cool it further.
- Slide your foot in, seat your heel fully and check your big toe is in its pocket. Repeat the rinse and fit on the second boot, then fasten the straps if fitted.
- Walk around for 10–15 minutes as the boots cool. Let them cool fully before judging the fit.
Solite videos
See how Solite 2.0 boots are built, how to heat-mould them and how to get them on and off.
Solite 2.0 Feature Video
A quick look at the design and features of the Solite 2.0 boots.
Solite 2022 Heat Molding Video
Follow the steps for heat-moulding Solite 2.0 boots to your feet.
Solite On/Off Technique
See how to get your Solite boots on and off.
Accessories fit guide

Solite Convertible hat sizing
Wrap a soft tape around your head where the hat will sit. Adjust the rear strap and chin strap for a secure fit.
| Size | Head circumference (cm) |
|---|---|
| S/M | 53–57 |
| Between sizes | 58 |
| L/XL | 59–64 |
At 58 cm, choose L/XL if you want more coverage or S/M if you prefer less.

Heat Booster sock sizes
| Size | Knit Split-Toe (UK) | 1 mm neoprene (UK) |
|---|---|---|
| S | 4–6 | 4–6.5 |
| M | 7–9 | 7–8.5 |
| L | 10–12 | 9–10.5 |
| XL | — | 11–12+ |

Solite rash guard fit
Start with your usual T-shirt size. The Convertible Neo-Front and Heat Shield are designed to sit close to the body. If you’re between sizes or prefer a little more room, choose the larger size.
Need a hand with fit?
Size measurements and fitting guidance are based on Solite’s manufacturer information. Check the sizing notes on your particular model.
